Project LiftOff: Difference between revisions
From NHRL
Content added Content deleted
JimKazmer2 (talk | contribs) No edit summary |
JimKazmer2 (talk | contribs) No edit summary |
||
| Line 11: | Line 11: | ||
* Rev-1.1 May 2019 |
* Rev-1.1 May 2019 |
||
** switched from 8" Aluminum rings to 9" AR-500 ring with tooth (and hand cut HDPE) |
** switched from 8" Aluminum rings to 9" AR-500 ring with tooth (and hand cut HDPE) |
||
*** this AR-500 tooth |
*** this AR-500 tooth proved to be too pointed and became embedded in arena wall several times |
||
[[File:Project LiftOff b May-2019.jpg|alt=|thumb|Project LiftOff - May 2019 (rev 1.1)]] |
[[File:Project LiftOff b May-2019.jpg|alt=|thumb|Project LiftOff - May 2019 (rev 1.1)]] |
||
[[File:Project LiftOff c Aug-2019.jpg|alt=|thumb|Project LiftOff - August 2019 (rev 1.2)]] |
[[File:Project LiftOff c Aug-2019.jpg|alt=|thumb|Project LiftOff - August 2019 (rev 1.2)]] |
||
Revision as of 19:57, 9 March 2021
Project LiftOff is a 3lbs MeltyBrain (a robot that moves using translations drift as its entire body spins at 1000 to 3000 RPM.
For 2021, Project LiftOff is beginning its third major revision.
- Rev-1.0 : March 2019
- Processor: Arduino Nano
- Accelerometer: common MPU 6050 (+/- 16g 12 bits)
- Receiver Interface: standard RC-PWM into UART
- Motor Control: OneShot125 via PWM manipulation @ ~800Hz
- External Sensors: none
- Rev-1.1 May 2019
- switched from 8" Aluminum rings to 9" AR-500 ring with tooth (and hand cut HDPE)
- this AR-500 tooth proved to be too pointed and became embedded in arena wall several times
- switched from 8" Aluminum rings to 9" AR-500 ring with tooth (and hand cut HDPE)
- Rev-2.0 : 2020
- Processor: Teensy 4.0
- Accelerometer: none… used motor eRPM telemetry from ESCs via bidirectional dShot
- Receiver Interface: RC-SBUS into UART
- Motor Control: dShot600 via SPI manipulation @ 8000Hz
- External Sensors: active IR
- CNC'd HDPE body
- New 8" AR-500 ring and tooth (with a more blunt tip)
- Rev-3 : 2021 Same electronics as Rev-2; improved algorithm, wheel orientation, and return to accelerometer.
- Processor: Teensy 4.0
- Accelerometer: H3LIS331DL (+/- 400g 16 bits)
- Receiver Interface: RC-SBUS into UART
- Motor Control: dShot600 via SPI manipulation @ 8000Hz
- External Sensors: active IR
Robot Facts
The first appearance was at the March 2019 NHRL event. The very first version used an 8" diameter aluminum pipe cut into two 1/2" thick slices with a notch cut out for the AR500 tooth (with two bolt holes).
| Driver | Andrew Kazmer (mostly) Jim Kazmer (sometimes) |
| Weight Class | 3lb |
| Body Material | HDPE (CNC) + AR500 |
| Weapon | Horizontal Body Spinner, 1360 grams |
| Weapon Drive | see below |
| Drive | 2 x FliteTest 2218 Brushless Motor, direct drive |
| Power | 2x4S 650mah LiPo |
T
Tournament Results
2020
| NHRL January | Did Not Compete |
| NHRL July 1 | |
| NHRL July 2 | |
| NHRL September | |
| NHRL November | Did Not Compete |
